Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Add support for the WL1835MOD cape.
This cape conflicts with the eMMC and HDMI on board the BeagleBone Black.

This change requires that the board be booted from the SD card slot by
holding the user/boot button down at power on and reset.

Signed-off-by: Eyal Reizer <eyalr@ti.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Adds a dts file for the Arrow BeagleBone Black Industrial board.
This BBB variant differs in that it uses an industrial temp rated
ADV7511W HDMI encoder rather than the NXP HDMI encoder on the
tradtional BBB.

Signed-off-by: Matt Porter <mporter@konsulko.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

Added pin mux definitions for collision and carrier sense errors coming
from the ethernet phy. Without these two signals the MAC ends up ignoring
the errors detected by the PHY which end up causing a lower throughput
problem when the phy is in half duplex mode such as connected through a hub.

Fixes: 2ba35493 (ARM: dts: am335x-bone*: add DT for BeagleBone Black)
Cc: Koen Kooi <koen@dominion.thruhere.net>
Cc: Tom Rini <trini@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

https://groups.google.com/d/msg/beagleboard/634Xm1m3XA8/B028x1FzAyAJ



Reported-by: Mark A. Yoder <mark.a.yoder@gmail.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>

This adds the devicetree bindings for the STMPE ADC.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>

This adds an ADC driver for the STMPE device using the industrial
input/output interface. The driver supports raw reading of values.
The driver depends on the MFD STMPE driver. If the touchscreen
block is enabled too, only four of the 8 ADC channels are available.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>

Move defines that are ADC related to the header of the overlying mfd,
so they can be used from multiple sub-devices.

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>