- Nov 20, 2013
-
-
Steven Rostedt (Red Hat) authored
-
Steven Rostedt (Red Hat) authored
This is the 3.2.52 stable release
-
- Oct 26, 2013
-
-
Ben Hutchings authored
-
Marc Kleine-Budde authored
commit d5a7b406 upstream. In patch 0d1862ea can: flexcan: fix flexcan_chip_start() on imx6 the loop in flexcan_chip_start() that iterates over all mailboxes after the soft reset of the CAN core was removed. This loop put all mailboxes (even the ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63, this aborts any pending TX messages. After a cold boot there is random garbage in the mailboxes, which leads to spontaneous transmit of CAN frames during first activation. Further if the interface was disabled with a pending message (usually due to an error condition on the CAN bus), this message is retransmitted after enabling the interface again. This patch fixes the regression by: 1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX FIFO, 8 is used by TX. 2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that mailbox is aborted. Cc: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> [bwh: Backported to 3.2: - Adjust context - Hardware local echo is still enabled] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Claudiu Manoil authored
commit b98b8bab upstream. This is primarily to address transmission timeout occurrences, when multiple H/W Tx queues are being used concurrently. Because in the priority scheduling mode the controller does not service the Tx queues equally (but in ascending index order), Tx timeouts are being triggered rightaway for a basic test with multiple simultaneous connections like: iperf -c <server_ip> -n 100M -P 8 resulting in kernel trace: NETDEV WATCHDOG: eth1 (fsl-gianfar): transmit queue <X> timed out ------------[ cut here ]------------ WARNING: at net/sched/sch_generic.c:255 ... and controller reset during intense traffic, and possibly further complications. This patch changes the default H/W Tx scheduling setting (TXSCHED) for multi-queue devices, from priority scheduling mode to a weighted round robin mode with equal weights for all H/W Tx queues, and addresses the issue above. Signed-off-by:
Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
David Rientjes authored
commit 4b59e6c4 upstream. On large systems with a lot of memory, walking all RAM to determine page types may take a half second or even more. In non-blockable contexts, the page allocator will emit a page allocation failure warning unless __GFP_NOWARN is specified. In such contexts, irqs are typically disabled and such a lengthy delay may even result in NMI watchdog timeouts. To fix this, suppress the page walk in such contexts when printing the page allocation failure warning. Signed-off-by:
David Rientjes <rientjes@google.com> Cc: Mel Gorman <mgorman@suse.de> Acked-by:
Michal Hocko <mhocko@suse.cz> Cc: Dave Hansen <dave@linux.vnet.ibm.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Lv Zheng authored
commit 06a8566b upstream. This patch fixes the issues indicated by the test results that ipmi_msg_handler() is invoked in atomic context. BUG: scheduling while atomic: kipmi0/18933/0x10000100 Modules linked in: ipmi_si acpi_ipmi ... CPU: 3 PID: 18933 Comm: kipmi0 Tainted: G AW 3.10.0-rc7+ #2 Hardware name: QCI QSSC-S4R/QSSC-S4R, BIOS QSSC-S4R.QCI.01.00.0027.070120100606 07/01/2010 ffff8838245eea00 ffff88103fc63c98 ffffffff814c4a1e ffff88103fc63ca8 ffffffff814bfbab ffff88103fc63d28 ffffffff814c73e0 ffff88103933cbd4 0000000000000096 ffff88103fc63ce8 ffff88102f618000 ffff881035c01fd8 Call Trace: <IRQ> [<ffffffff814c4a1e>] dump_stack+0x19/0x1b [<ffffffff814bfbab>] __schedule_bug+0x46/0x54 [<ffffffff814c73e0>] __schedule+0x83/0x59c [<ffffffff81058853>] __cond_resched+0x22/0x2d [<ffffffff814c794b>] _cond_resched+0x14/0x1d [<ffffffff814c6d82>] mutex_lock+0x11/0x32 [<ffffffff8101e1e9>] ? __default_send_IPI_dest_field.constprop.0+0x53/0x58 [<ffffffffa09e3f9c>] ipmi_msg_handler+0x23/0x166 [ipmi_si] [<ffffffff812bf6e4>] deliver_response+0x55/0x5a [<ffffffff812c0fd4>] handle_new_recv_msgs+0xb67/0xc65 [<ffffffff81007ad1>] ? read_tsc+0x9/0x19 [<ffffffff814c8620>] ? _raw_spin_lock_irq+0xa/0xc [<ffffffffa09e1128>] ipmi_thread+0x5c/0x146 [ipmi_si] ... Also Tony Camuso says: We were getting occasional "Scheduling while atomic" call traces during boot on some systems. Problem was first seen on a Cisco C210 but we were able to reproduce it on a Cisco c220m3. Setting CONFIG_LOCKDEP and LOCKDEP_SUPPORT to 'y' exposed a lockdep around tx_msg_lock in acpi_ipmi.c struct acpi_ipmi_device. ================================= [ INFO: inconsistent lock state ] 2.6.32-415.el6.x86_64-debug-splck #1 --------------------------------- inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. ksoftirqd/3/17 [HC0[0]:SC1[1]:HE1:SE0] takes: (&ipmi_device->tx_msg_lock){+.?...}, at: [<ffffffff81337a27>] ipmi_msg_handler+0x71/0x126 {SOFTIRQ-ON-W} state was registered at: [<ffffffff810ba11c>] __lock_acquire+0x63c/0x1570 [<ffffffff810bb0f4>] lock_acquire+0xa4/0x120 [<ffffffff815581cc>] __mutex_lock_common+0x4c/0x400 [<ffffffff815586ea>] mutex_lock_nested+0x4a/0x60 [<ffffffff8133789d>] acpi_ipmi_space_handler+0x11b/0x234 [<ffffffff81321c62>] acpi_ev_address_space_dispatch+0x170/0x1be The fix implemented by this change has been tested by Tony: Tested the patch in a boot loop with lockdep debug enabled and never saw the problem in over 400 reboots. Reported-and-tested-by:
Tony Camuso <tcamuso@redhat.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Reviewed-by:
Huang Ying <ying.huang@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Ian Abbott authored
commit 677a3156 upstream. The `insn_bits` handler `ni_65xx_dio_insn_bits()` has a `for` loop that currently writes (optionally) and reads back up to 5 "ports" consisting of 8 channels each. It reads up to 32 1-bit channels but can only read and write a whole port at once - it needs to handle up to 5 ports as the first channel it reads might not be aligned on a port boundary. It breaks out of the loop early if the next port it handles is beyond the final port on the card. It also breaks out early on the 5th port in the loop if the first channel was aligned. Unfortunately, it doesn't check that the current port it is dealing with belongs to the comedi subdevice the `insn_bits` handler is acting on. That's a bug. Redo the `for` loop to terminate after the final port belonging to the subdevice, changing the loop variable in the process to simplify things a bit. The `for` loop could now try and handle more than 5 ports if the subdevice has more than 40 channels, but the test `if (bitshift >= 32)` ensures it will break out early after 4 or 5 ports (depending on whether the first channel is aligned on a port boundary). (`bitshift` will be between -7 and 7 inclusive on the first iteration, increasing by 8 for each subsequent operation.) Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [Ian Abbott: This patch applies to kernels 2.6.34.y through to 3.5.y inclusive.] Signed-off-by:
-
Theodore Ts'o authored
commit 0e9a9a1a upstream. When trying to mount a file system which does not contain a journal, but which does have a orphan list containing an inode which needs to be truncated, the mount call with hang forever in ext4_orphan_cleanup() because ext4_orphan_del() will return immediately without removing the inode from the orphan list, leading to an uninterruptible loop in kernel code which will busy out one of the CPU's on the system. This can be trivially reproduced by trying to mount the file system found in tests/f_orphan_extents_inode/image.gz from the e2fsprogs source tree. If a malicious user were to put this on a USB stick, and mount it on a Linux desktop which has automatic mounts enabled, this could be considered a potential denial of service attack. (Not a big deal in practice, but professional paranoids worry about such things, and have even been known to allocate CVE numbers for such problems.) -js: This is a fix for CVE-2013-2015. Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> Reviewed-by:
Zheng Liu <wenqing.lz@taobao.com> Acked-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Henrik Rydberg authored
commit 0fc86eca upstream. Some error paths do not set a result, leading to the (false) assumption that the value may be used uninitialized. Set results for those paths as well. Signed-off-by:
Henrik Rydberg <rydberg@euromail.se> Signed-off-by:
Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by:
-
Florian Wolter authored
commit 526867c3 upstream. The halted state of a endpoint cannot be cleared over CLEAR_HALT from a user process, because the stopped_td variable was overwritten in the handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will refuse the reset and communication with device can not run over this endpoint. https://bugzilla.kernel.org/show_bug.cgi?id=60699 Signed-off-by:
Florian Wolter <wolly84@web.de> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
Dan Carpenter authored
commit 58f09e00 upstream. The arg64 struct has a hole after ->buf_size which isn't cleared. Or if any of the calls to copy_from_user() fail then that would cause an information leak as well. This was assigned CVE-2013-2147. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Mike Miller <mike.miller@hp.com> Signed-off-by:
-
Dan Carpenter authored
commit 627aad1c upstream. The pciinfo struct has a two byte hole after ->dev_fn so stack information could be leaked to the user. This was assigned CVE-2013-2147. Signed-off-by:
-
Sasha Levin authored
commit 46a7c17d upstream. iscsi_if_send_reply() may return -ESRCH if there were no targets to send data to. Currently we're ignoring this value and looping in attempt to do it over and over, which will usually lead in a hung task like this one: [ 4920.817298] INFO: task trinity:9074 blocked for more than 120 seconds. [ 4920.818527] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 4920.819982] trinity D 0000000000000000 5504 9074 2756 0x00000004 [ 4920.825374] ffff880003961a98 0000000000000086 ffff8800001aa000 ffff8800001aa000 [ 4920.826791] 00000000001d4340 ffff880003961fd8 ffff880003960000 00000000001d4340 [ 4920.828241] 00000000001d4340 00000000001d4340 ffff880003961fd8 00000000001d4340 [ 4920.833231] [ 4920.833519] Call Trace: [ 4920.834010] [<ffffffff826363fa>] schedule+0x3a/0x50 [ 4920.834953] [<ffffffff82634ac9>] __mutex_lock_common+0x209/0x5b0 [ 4920.836226] [<ffffffff81af805d>] ? iscsi_if_rx+0x2d/0x990 [ 4920.837281] [<ffffffff81053943>] ? sched_clock+0x13/0x20 [ 4920.838305] [<ffffffff81af805d>] ? iscsi_if_rx+0x2d/0x990 [ 4920.839336] [<ffffffff82634eb0>] mutex_lock_nested+0x40/0x50 [ 4920.840423] [<ffffffff81af805d>] iscsi_if_rx+0x2d/0x990 [ 4920.841434] [<ffffffff810dffed>] ? sub_preempt_count+0x9d/0xd0 [ 4920.842548] [<ffffffff82637bb0>] ? _raw_read_unlock+0x30/0x60 [ 4920.843666] [<ffffffff821f71de>] netlink_unicast+0x1ae/0x1f0 [ 4920.844751] [<ffffffff821f7997>] netlink_sendmsg+0x227/0x350 [ 4920.845850] [<ffffffff821857bd>] ? sock_update_netprioidx+0xdd/0x1b0 [ 4920.847060] [<ffffffff82185732>] ? sock_update_netprioidx+0x52/0x1b0 [ 4920.848276] [<ffffffff8217f226>] sock_aio_write+0x166/0x180 [ 4920.849348] [<ffffffff810dfe41>] ? get_parent_ip+0x11/0x50 [ 4920.850428] [<ffffffff811d0d9a>] do_sync_write+0xda/0x120 [ 4920.851465] [<ffffffff810dffed>] ? sub_preempt_count+0x9d/0xd0 [ 4920.852579] [<ffffffff810dfe41>] ? get_parent_ip+0x11/0x50 [ 4920.853608] [<ffffffff81791887>] ? security_file_permission+0x27/0xb0 [ 4920.854821] [<ffffffff811d0f4c>] vfs_write+0x16c/0x180 [ 4920.855781] [<ffffffff811d104f>] sys_write+0x4f/0xa0 [ 4920.856798] [<ffffffff82638e79>] system_call_fastpath+0x16/0x1b [ 4920.877487] 1 lock held by trinity/9074: [ 4920.878239] #0: (rx_queue_mutex){+.+...}, at: [<ffffffff81af805d>] iscsi_if_rx+0x2d/0x990 [ 4920.880005] Kernel panic - not syncing: hung_task: blocked tasks Signed-off-by:
Sasha Levin <levinsasha928@gmail.com> Acked-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Ben Hutchings authored
This reverts commit de77b795, which was commit f6e80abe upstream. This fix was only appropriate for Linux 3.7 onward, and introduced a regression when applied to earlier versions. Signed-off-by:
-
Jan Kara authored
commit 17b7f7cf upstream. Refuse RW mount of isofs filesystem. So far we just silently changed it to RO mount but when the media is writeable, block layer won't notice this change and thus will think device is used RW and will block eject button of the drive. That is unexpected by users because for non-writeable media eject button works just fine. Userspace mount(8) command handles this just fine and retries mounting with MS_RDONLY set so userspace shouldn't see any regression. Plus any tool mounting isofs is likely confronted with the case of read-only media where block layer already refuses to mount the filesystem without MS_RDONLY set so our behavior shouldn't be anything new for it. Reported-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
-
Vasily Titskiy authored
commit 9e0bf92c upstream. The DuoSense touchscreen device causes a 10 second timeout. This fix removes the delay. Signed-off-by:
Vasily Titskiy <qehgt0@gmail.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Stefan Kriwanek authored
commit 06bb5219 upstream. Some devices of the "Speedlink VAD Cezanne" model need more aggressive fixing than already done. I made sure through testing that this patch would not interfere with the proper working of a device that is bug-free. (The driver drops EV_REL events with abs(val) >= 256, which are not achievable even on the highest laser resolution hardware setting.) Signed-off-by:
Stefan Kriwanek <mail@stefankriwanek.de> Signed-off-by:
-
Lino Sanfilippo authored
commit 03a1cec1 upstream. Boyd Yang reported a problem for the case that multiple threads of the same thread group are waiting for a reponse for a permission event. In this case it is possible that some of the threads are never woken up, even if the response for the event has been received (see http://marc.info/?l=linux-kernel&m=131822913806350&w=2 ). The reason is that we are currently merging permission events if they belong to the same thread group. But we are not prepared to wake up more than one waiter for each event. We do wait_event(group->fanotify_data.access_waitq, event->response || atomic_read(&group->fanotify_data.bypass_perm)); and after that event->response = 0; which is the reason that even if we woke up all waiters for the same event some of them may see event->response being already set 0 again, then go back to sleep and block forever. With this patch we avoid that more than one thread is waiting for a response by not merging permission events for the same thread group any more. Reported-by:
Boyd Yang <boyd.yang@gmail.com> Signed-off-by:
Lino Sanfilippo <LinoSanfilipp@gmx.de> Signed-off-by:
Eric Paris <eparis@redhat.com> Signed-off-by:
-
Andi Kleen authored
commit 89365e6c upstream. Need to check for /dev/zero. Most likely more strings are missing too. Signed-off-by:
Andi Kleen <ak@linux.intel.com> Link: http://lkml.kernel.org/r/1366848182-30449-1-git-send-email-andi@firstfloor.org Signed-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Peter Zijlstra authored
commit 95cf59ea upstream. Jiri reported that he could trigger the WARN_ON_ONCE() in perf_cgroup_switch() using sw-events. This is because sw-events share a cpuctx with multiple PMUs. Use the ->unique_pmu pointer to limit the pmu iteration to unique cpuctx instances. Reported-and-Tested-by:
Jiri Olsa <jolsa@redhat.com> Signed-off-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/n/tip-so7wi2zf3jjzrwcutm2mkz0j@git.kernel.org Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Peter Zijlstra authored
commit 3f1f3320 upstream. Stephane thought the perf_cpu_context::active_pmu name confusing and suggested using 'unique_pmu' instead. This pointer is a pointer to a 'random' pmu sharing the cpuctx instance, therefore limiting a for_each_pmu loop to those where cpuctx->unique_pmu matches the pmu we get a loop over unique cpuctx instances. Suggested-by:
Stephane Eranian <eranian@google.com> Signed-off-by:
-
Li Zefan authored
commit f169007b upstream. If we pass fd of memory.usage_in_bytes of cgroup A to cgroup.event_control of cgroup B, then we won't get memory usage notification from A but B! What's worse, if A and B are in different mount hierarchy, we'll end up accessing NULL pointer! Disallow this kind of invalid usage. Signed-off-by:
Li Zefan <lizefan@huawei.com> Acked-by:
Kirill A. Shutemov <kirill@shutemov.name> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Ben Hutchings authored
This bug fix is only for stable branches older than 3.10. The bug was fixed upstream by commit 2768935a ('sfc: reuse pages to avoid DMA mapping/unmapping costs'), but that change is totally unsuitable for stable. Commit b590ace0 ('sfc: Fix efx_rx_buf_offset() in the presence of swiotlb') added an explicit page_offset member to struct efx_rx_buffer, which must be set consistently with the u.page and dma_addr fields. However, it failed to add the necessary assignment in efx_resurrect_rx_buffer(). It also did not correct the calculation of efx_rx_buffer::dma_addr in efx_resurrect_rx_buffer(), which assumes that DMA-mapping a page will result in a page-aligned DMA address (exactly what swiotlb violates). Add the assignment of efx_rx_buffer::page_offset and change the calculation of dma_addr to make use of it. Signed-off-by:
Ben Hutchings <bhutchings@solarflare.com>
-
Jason Wang authored
commit ece793fc upstream. We try to linearize part of the skb when the number of iov is greater than MAX_SKB_FRAGS. This is not enough since each single vector may occupy more than one pages, so zerocopy_sg_fromiovec() may still fail and may break the guest network. Solve this problem by calculate the pages needed for iov before trying to do zerocopy and switch to use copy instead of zerocopy if it needs more than MAX_SKB_FRAGS. This is done through introducing a new helper to count the pages for iov, and call uarg->callback() manually when switching from zerocopy to copy to notify vhost. We can do further optimization on top. This bug were introduced from b92946e2 (macvtap: zerocopy: validate vectors before building skb). Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Ben Hutchings authored
This reverts commit 9e443904, which was commit 57ab0485 upstream. Taking the semaphore here leads to sleeping in atomic context. This was fixed in mainline commit a0c516cb ("zram: don't grab mutex in zram_slot_free_noity") but that is too difficult to backport. Signed-off-by:
-
Chen Gang authored
commit 5676005a upstream. need set '\0' for 'local_buffer'. SPLPAR_MAXLENGTH is 1026, RTAS_DATA_BUF_SIZE is 4096. so the contents of rtas_data_buf may truncated in memcpy. if contents are really truncated. the splpar_strlen is more than 1026. the next while loop checking will not find the end of buffer. that will cause memory access violation. Signed-off-by:
Chen Gang <gang.chen@asianux.com> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Greg Ungerer authored
commit f84f52a5 upstream. There is a lot of years of collected cruft in the m68knommu linker script. Clean it all up and use the well defined linker script support macros. Support is maintained for building both ROM/FLASH based and RAM based setups. No major changes to section layouts, though the rodata section is now lumped in with the read/write data section. Signed-off-by:
Greg Ungerer <gerg@uclinux.org> Signed-off-by:
-
Greg Ungerer authored
commit ed865e31 upstream. Use the non-MMU linker script for ColdFire builds when we are building for MMU enabled. The image layout is correct for loading on existing ColdFire dev boards. The only addition required to the current non-MMU linker script is to add support for the fixup section. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Acked-by:
Matt Waddel <mwaddel@yahoo.com> Acked-by:
Kurt Mahan <kmahan@xmission.com> Signed-off-by:
-
Greg Ungerer authored
commit 40c1b9cf upstream. The merge of m68knommu left the linker scripts a little disorganized. Some consistent naming and squashing two of scripts that just include others can simplify things a lot. So merge the two simple including scripts, and rename the nommu script to be consistent with the existing m68k linker scripts. Signed-off-by:
-
Julius Werner authored
commit 481f2d4f upstream. The USB hub driver's event handler contains a check to catch SuperSpeed devices that transitioned into the SS.Inactive state and tries to fix them with a reset. It decides whether to do a plain hub port reset or call the usb_reset_device() function based on whether there was a device attached to the port. However, there are device/hub combinations (found with a JetFlash Transcend mass storage stick (8564:1000) on the root hub of an Intel LynxPoint PCH) which can transition to the SS.Inactive state on disconnect (and stay there long enough for the host to notice). In this case, above-mentioned reset check will call usb_reset_device() on the stale device data structure. The kernel will send pointless LPM control messages to the no longer connected device address and can even cause several 5 second khubd stalls on some (buggy?) host controllers, before finally accepting the device's fate amongst a flurry of error messages. This patch makes the choice of reset dependent on the port status that has just been read from the hub in addition to the existence of an in-kernel data structure for the device, and only proceeds with the more extensive reset if both are valid. Signed-off-by:
Julius Werner <jwerner@chromium.org> Signed-off-by:
-
Oleg Nesterov authored
commit 776164c1 upstream. debugfs_remove_recursive() is wrong, 1. it wrongly assumes that !list_empty(d_subdirs) means that this dir should be removed. This is not that bad by itself, but: 2. if d_subdirs does not becomes empty after __debugfs_remove() it gives up and silently fails, it doesn't even try to remove other entries. However ->d_subdirs can be non-empty because it still has the already deleted !debugfs_positive() entries. 3. simple_release_fs() is called even if __debugfs_remove() fails. Suppose we have dir1/ dir2/ file2 file1 and someone opens dir1/dir2/file2. Now, debugfs_remove_recursive(dir1/dir2) succeeds, and dir1/dir2 goes away. But debugfs_remove_recursive(dir1) silently fails and doesn't remove this directory. Because it tries to delete (the already deleted) dir1/dir2/file2 again and then fails due to "Avoid infinite loop" logic. Test-case: #!/bin/sh cd /sys/kernel/debug/tracing echo 'p:probe/sigprocmask sigprocmask' >> kprobe_events sleep 1000 < events/probe/sigprocmask/id & echo -n >| kprobe_events [ -d events/probe ] && echo "ERR!! failed to rm probe" And after that it is not possible to create another probe entry. With this patch debugfs_remove_recursive() skips !debugfs_positive() files although this is not strictly needed. The most important change is that it does not try to make ->d_subdirs empty, it simply scans the whole list(s) recursively and removes as much as possible. Link: http://lkml.kernel.org/r/20130726151256.GC19472@redhat.com Acked-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Salman Qazi authored
commit 9c5da09d upstream. An rmdir pushes css's ref count to zero. However, if the associated directory is open at the time, the dentry ref count is non-zero. If the fd for this directory is then passed into perf_event_open, it does a css_get(). This bounces the ref count back up from zero. This is a problem by itself. But what makes it turn into a crash is the fact that we end up doing an extra dput, since we perform a dput when css_put sees the ref count go down to zero. css_tryget() does not fall into that trap. So, we use that instead. Reproduction test-case for the bug: #include <unistd.h> #include <sys/types.h> #include <sys/stat.h> #include <fcntl.h> #include <linux/unistd.h> #include <linux/perf_event.h> #include <string.h> #include <errno.h> #include <stdio.h> #define PERF_FLAG_PID_CGROUP (1U << 2) int perf_event_open(struct perf_event_attr *hw_event_uptr, pid_t pid, int cpu, int group_fd, unsigned long flags) { return syscall(__NR_perf_event_open,hw_event_uptr, pid, cpu, group_fd, flags); } /* * Directly poke at the perf_event bug, since it's proving hard to repro * depending on where in the kernel tree. what moved? */ int main(int argc, char **argv) { int fd; struct perf_event_attr attr; memset(&attr, 0, sizeof(attr)); attr.exclude_kernel = 1; attr.size = sizeof(attr); mkdir("/dev/cgroup/perf_event/blah", 0777); fd = open("/dev/cgroup/perf_event/blah", O_RDONLY); perror("open"); rmdir("/dev/cgroup/perf_event/blah"); sleep(2); perf_event_open(&attr, fd, 0, -1, PERF_FLAG_PID_CGROUP); perror("perf_event_open"); close(fd); return 0; } Signed-off-by:
Salman Qazi <sqazi@google.com> Signed-off-by:
-
Daniel Santos authored
commit 65478428 upstream. Prior to this patch the following code breaks: /** * multiline_example - this breaks kernel-doc */ #define multiline_example( \ myparam) Producing this error: Error(somefile.h:983): cannot understand prototype: 'multiline_example( \ ' This patch fixes the issue by appending all lines ending in a blackslash (optionally followed by whitespace), removing the backslash and any whitespace after it prior to appending (just like the C pre-processor would). This fixes a break in kerel-doc introduced by the additions to rbtree.h. Signed-off-by:
Daniel Santos <daniel.santos@pobox.com> Cc: Randy Dunlap <rdunlap@xenotime.net> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by:
-
Kirill Tkhai authored
[ Upstream commit 7a3b0f89 ] Pass 1 in %o1 to indicate that syscall_trace accounts exit. Signed-off-by:
Kirill Tkhai <tkhai@yandex.ru> CC: David Miller <davem@davemloft.net> Signed-off-by:
-
Kirill Tkhai authored
[ Upstream commit ab2abda6 ] (From v1 to v2: changed comment) On the way linux_sparc_syscall32->linux_syscall_trace32->goto 2f, register %o5 doesn't clear its second 32-bit. Fix that. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 63d49966 ] Reported-by:
-
Kirill Tkhai authored
[ Upstream commit 61d9b935 ] The functions __down_read __down_read_trylock __down_write __down_write_trylock __up_read __up_write __downgrade_write are implemented inline, so remove corresponding EXPORT_SYMBOLs (They lead to compile errors on RT kernel). Signed-off-by:
-
Kirill Tkhai authored
[ Upstream commit 1c2696cd ] 1)Use kvmap_itlb_longpath instead of kvmap_dtlb_longpath. 2)Handle page #0 only, don't handle page #1: bleu -> blu (KERNBASE is 0x400000, so #1 does not exist too. But everything is possible in the future. Fix to not to have problems later.) 3)Remove unused kvmap_itlb_nonlinear. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 21af8107 ] Meelis Roos reports a crash in esp_free_lun_tag() in the presense of a disk which has died. The issue is that when we issue an autosense command, we do so by hijacking the original command that caused the check-condition. When we do so we clear out the ent->tag[] array when we issue it via find_and_prep_issuable_command(). This is so that the autosense command is forced to be issued non-tagged. That is problematic, because it is the value of ent->tag[] which determines whether we issued the original scsi command as tagged vs. non-tagged (see esp_alloc_lun_tag()). And that, in turn, is what trips up the sanity checks in esp_free_lun_tag(). That function needs the original ->tag[] values in order to free up the tag slot properly. Fix this by remembering the original command's tag values, and having esp_alloc_lun_tag() and esp_free_lun_tag() use them. Reported-by:
Meelis Roos <mroos@linux.ee> Tested-by:
-
